Materials

Acrylic paint, UV print or textured coating: choosing a mural system

Three mural routes differ in adhesion, hiding power, weather resistance and cost per square metre. This guide sets out their boundaries by substrate, exposure and visual ambition so the route is chosen at design stage rather than on site.

At a glance. Three mural routes differ in adhesion, hiding power, weather resistance and cost per square metre. This guide sets out their boundaries by substrate, exposure and visual ambition so the route is chosen at design stage rather than on site.

What actually differs between the three routes

Hand-painted acrylic forms a pigment film on the substrate. Painters build colour in glazes, so the result has the best tonal depth and visible brushwork, and it suits complex imagery where a human hand is part of the value. The trade-off is labour: schedule grows roughly linearly with area, and very large walls need several painters working at once, which makes seam and colour consistency the hard part.

UV printing outputs the image onto a flexible medium that is applied to the wall, or directly onto a rigid board. It reproduces artwork precisely, delivers fast and has a low unit cost over large areas, but the image reads flat and the extra layer between artwork and wall can lift or lose adhesion through humidity and temperature cycles. Textured decorative coatings sit between the two: trowelled, rolled or rubbed to build a physical surface, then glazed. They are thick, washable and convincing for abstract, graded, stone-like or metal-like effects, but weak at figurative detail.

Let the substrate decide the adhesion build-up

On sound interior emulsion or putty, acrylic can be painted directly; a sealing primer is used where extra bite is needed. If the wall has elevated moisture content or rising damp, the water source must be fixed first, otherwise the paint film comes away with the skim coat. Bare concrete and cement are highly absorbent and alkaline, so the standard build-up is an alkali-resistant sealer, a thin skim coat, full drying, then paint. Metal sheet and old glazed tile need mechanical abrasion and an epoxy transition primer or they will delaminate in sheets.

Weathering changes the answer outdoors

Ultraviolet light and rain drive exterior failure. Use weather-grade acrylic or polyurethane pigments and finish with a clear anti-UV topcoat to form a water- and dirt-resistant film; a correctly built system normally holds its colour for three to five years. Where a wall is permanently rain-washed, near water or coastal, the economics of an acrylic system deteriorate and a more durable fluorocarbon print or a mineral exterior coating system is the safer choice. Orientation, overhang and rainfall exposure should be assessed honestly rather than applying one specification everywhere.

A practical specification sequence

Decide indoor or outdoor first, then substrate, then image complexity and budget. Complex interior imagery that wants brushwork points to hand-painted acrylic; very large repetitive interior graphics point to UV print; atmosphere and texture with abstract imagery point to decorative coatings. The three are not mutually exclusive: a common scheme uses a textured coating for the broad background, hand-painted acrylic for the focal image and printed colour separation for small signage. Layering must be fixed at drawing stage or the joins show on site.

Maintenance belongs in the comparison. A damaged hand-painted area can be retouched in place with manageable colour matching; a lifted or torn printed medium usually needs the whole panel replaced. Comparing three-to-five-year upkeep, not just the initial price, gives a much truer answer.

Go deeper

From the workshop

Technique library

101 in-depth technique guides grouped by capability.

Open library →

How we work

The seven-step process from brief to crated delivery, plus how quotations are built.

Read process →

Export & terms

Packing, documentation, freight terms and what an overseas buyer needs to confirm.

Read terms →
Also in the library

Three ways into the material

Technique articles explain how the work is made. Buyer insights explain how a project is specified, approved and accepted. The Q&A section answers the questions that come up before a quotation is agreed.

Technical knowledge base

22 in-depth articles on materials, processes, installation QA and applications.

Open section →

Buyer insights

7 long-form guides on contracts, site access, acceptance, briefing and aftercare.

Open section →

Buyer Q&A

96 practical answers grouped into 8 themes.

Open section →

Tell us what you are building

Send photos, dimensions, the destination country and your target date. You will get a technique recommendation, a reference price band and a production schedule - no obligation.

Request a quoteHow export works