Buyer Q&A

Care, repair and warranty

What counts as a defect, how common faults are diagnosed, how fast help arrives, and how to keep seasonal and outdoor work in service. Twelve aftercare questions.

About the figures on this page. Prices on this page are reference ranges for projects delivered inside China, shown in CNY. Export projects are quoted individually in USD after the brief, site conditions, freight and installation scope are confirmed. All ranges are indicative, not a fixed rate, and no outcome or exposure is promised.

12 questions

Care, repair and warranty

What counts as a defect, how common faults are diagnosed, how fast help arrives, and how to keep seasonal and outdoor work in service. Twelve aftercare questions.

How should a mural be cared for, and how long does it last?

Dust with a dry cloth or soft brush and wipe marks with water or a neutral cleaner; avoid hard brushes, strong acid or alkali, alcohol and pressure washers. A properly built interior acrylic mural commonly lasts five to ten years or more; exterior work fades over three to five years, which an anti-UV topcoat extends, after which local retouching is possible. A damp cloth is fine if wrung out - do not soak or scrub.

What should I do if a relief panel cracks?

Diagnose first. Hairline crazing usually comes from coating or filler shrinkage and can be filled; cracking along a joint needs the joint re-made; widespread cracking or detachment points to a hollow or damp substrate and requires the base to be rebuilt. The sequence is to find the cause (water, hollow areas, movement), remove loose material, reinforce the base, then re-skim and refinish. Surface-only patching is temporary. Impact damage normally shows a local dent or radiating crack, which helps distinguish it from a defect.

Can a faded mural be retouched?

Yes for local fading or wear: clean, match the colour, repaint, re-coat. Hand-painted work is relatively easy to blend. Where an entire exterior wall has faded from UV exposure, retouching is less effective and a full repaint or a unifying anti-UV clear coat is the better route. Expect a slight colour difference in local repairs; a controlled feathered transition is the standard method, and whole-surface repainting gives the most uniform result.

What if relief or a wall develops mould?

Mould is a moisture symptom, not a surface defect. Find the source first - leaks, rising damp, poor ventilation, a plumbing leak - then remove the growth, apply a fungicidal treatment and a mould-resistant sealing coat; where needed, rebuild the waterproof or damp-proof layer. Without solving the water source it recurs. Bleach may remove the stain briefly but can damage the coating; in persistently damp areas, consider cement or microcement instead of gypsum.

How do I troubleshoot an LED strip that has gone dark?

Check in order: is the driver powered and healthy, are connectors loose or oxidised, is the controller at fault, and finally is the strip itself broken. Damp connectors, an under-rated driver and aged strip are the usual causes, and the affected part can normally be replaced. Low-voltage strip can be changed by a competent installer, but mains-side work must be done by a qualified electrician - do not modify wiring yourself.

Can gypsum relief be wiped clean?

Light cleaning only: dust with a soft brush, then wipe marks with a slightly damp soft cloth and dry immediately. Do not use stiff brushes, scouring pads, strong acid or alkali, or large amounts of water, which wear the coating or soak into the gypsum and cause chalking. A wrung-out cloth that does not drip is fine, but keep water out of joints. In a normal interior, dusting once a quarter is enough.

How should an outdoor sculpture be maintained?

Rinse dust off periodically without aiming high-pressure water at joints; clean stainless steel with neutral detergent and a soft cloth, following the grain on brushed surfaces to avoid scratches; and inspect welds, base supports and protective coatings annually, touching up paint before rust develops. In coastal or acid-rain areas corrosion is faster, so shorten the interval. FRP benefits from regular cleaning and can be refurbished with a new coating after several years.

Will a 3D-printed part warp or fade?

It depends on the material. Resin parts are detailed but sensitive to UV and heat; PLA softens in high temperatures and should be kept out of outdoor or vehicle interiors; nylon and PETG are more weather-resistant. For outdoor use choose a weather-stable material and apply sanding, primer, topcoat and clear coat to slow fading considerably. Indoors, away from light and heat, parts last well; faded colour can be re-sprayed after cleaning and light sanding.

What information should a repair request include?

Four items: photographs (one close-up of the detail, one wider shot showing location), which part is affected (which wall, which component), the material or method, and the completion date or order number. With those, the cause can often be assessed in advance, the treatment estimated and a site visit judged necessary or not, saving several round trips. An order number helps locate the record but is not essential to begin.

How is out-of-warranty repair charged?

After the warranty period - commonly one year from completion - repairs are charged at actual cost: materials plus labour, plus travel where a site visit is needed. A proper process quotes first and waits for confirmation before starting. Damage caused by impact, unauthorised modification or failure to follow care instructions is chargeable even within the warranty period. Extended warranty terms can be negotiated and written into the contract; small issues that can be resolved by remote guidance do not require a visit fee.

Can materials from a derigged display be reused?

It depends on the component. Structural frames, luminaires, hardware and some formed elements can be recovered for the next campaign; printed graphics, paper items and fragile soft dressing are usually single-use. To save money, decide at design stage: standardised frames, demountable connections and generic luminaires allow the next campaign to reuse the structure and replace only the skin. Agree who derigs, stores and insures the components, with storage cost listed separately.

What routine care keeps an installation in service longest?

Three habits: clean and dust regularly using a method suited to the material; protect against impact, abrasion and prolonged direct sun; and inspect once a year - outdoors especially - for cracks, fading, loose fixings and failed lighting. Small cracks, peeling and looseness are cheap to fix early and expensive once they spread. Inspect outdoor work every six to twelve months, more often in coastal or acid-rain areas, and obtain a material-specific care sheet at handover.

Also in the library

Three ways into the material

Technique articles explain how the work is made. Buyer insights explain how a project is specified, approved and accepted. The Q&A section answers the questions that come up before a quotation is agreed.

Technical knowledge base

22 in-depth articles on materials, processes, installation QA and applications.

Open section →

Buyer insights

7 long-form guides on contracts, site access, acceptance, briefing and aftercare.

Open section →

Buyer Q&A

96 practical answers grouped into 8 themes.

Open section →

Tell us what you are building

Send photos, dimensions, the destination country and your target date. You will get a technique recommendation, a reference price band and a production schedule - no obligation.

Request a quoteHow export works